一、拆除前担保园地整洁拆除的地方内不灰尘、严重影响物，提高认识空气中白皙。查抄机器设备有不筹划俱备，打比方，沸石转轮层面、传动装置有限公司、封严配件、线路数据接口等组件。品质保证核查：进行成度仪验测转轮拆除面的立休度，粗差应≤0.1mm/m，以免因拆除面倾斜度引发持续运行偏疼。　　1、 Before installation, ensure that the site is clean and there are no debris or obstacles in the installation area, and ensure that the ground is flat. Check if the equipment is fully prepared, such as the zeolite wheel body, transmission motor, sealing components, pipeline interfaces, and other components. Quality review: Use a level to check the flatness of the installation surface of the wheel, with an error of ≤ 0.1mm/m, to avoid eccentricity caused by the inclination of the installation surface.　　二、的点拆下来步：1.主体结构就绪与市场定位手机：公司功夫：认识自己10吨级起重机器设施设备机暂停公司，公司带与机器设施设备战斗面需垫产品加固垫，制止刮痕外貌纳米涂层；精细市场定位手机：依靠时激光行业对中仪研究生调剂机器设施设备能力度，使转驱动轴线与本质其中线随机误差≤0.5mm，事关扭转弹簧踏实性。　　2、 Core installation steps: 1. Main body positioning and installation: Lifting operation: Use a 10 ton crane for lifting, and rubber protective pads should be placed on the contact surface between the lifting belt and the equipment to prevent scratching the surface coating; Accurate positioning: Adjust the levelness of the equipment through a laser alignment instrument to ensure that the deviation between the wheel axis and the foundation centerline is ≤ 0.5mm, ensuring smooth rotation.　　排水通管线线系统毗连：进气排水通管线线：接收DN300不绣钢排水通管线线，与机器接头活套法兰毗连时，螺母固定挨次严格执行“对角线法例”，分三遍不知不觉打紧至生态红线划定扭距值；泄压阀排水通管线线：设备45°90度弯头核减气体流动摩擦力，排水通管线线支撑跨距≤3米，避免 因车重让排水通管线线变弯；脱附管线：毗连至RTO（蓄快热式热防氧化炉）的排水通管线线需包着10mm厚硅酸铝纤维材料棉恒温层，核减能量浪费。　　Pipeline system connection: Inlet pipeline: DN300 stainless steel pipeline is used. When connecting with the equipment interface flange, the bolt tightening sequence follows the "diagonal rule" and is gradually tightened in three times to the specified torque value; Exhaust pipe: Install a 45 ° elbow to reduce airflow resistance, with a pipe support spacing of ≤ 3 meters to avoid deformation of the pipe due to its own weight; Detached air duct: The pipeline connected to RTO (Regenerative Thermal Oxidizer) needs to be wrapped with a 10mm thick aluminum silicate fiber cotton insulation layer to reduce heat loss.　　沸石转轮取下：沸石添补：将预应对后的沸石顆粒（颗粒直径2-4mm）评均添补至转轮蜂窝缝隙中，添补体积密度合理在600kg/m?，巧用激振台助力抓实，有效确保无院子；密封性规划：取下专利证书卡定模块，途经的时候定位转槽与卡定弧槽的下颌骨，使一是圆板和第三圆板与转轮方框的洞眼≤0.1mm，防范排放物暴露。　　Zeolite wheel assembly: Zeolite filling: Fill the pre treated zeolite particles (particle size 2-4mm) evenly into the honeycomb pores of the wheel, with a filling density controlled at 600kg/m? Use a vibration table to assist in compaction, ensuring no gaps; Sealing structure: Install patented locking components, and through the engagement of the limiting groove and the locking arc groove, ensure that the gap between the first circular plate and the second circular plate and the wheel frame is ≤ 0.1mm to prevent exhaust gas leakage.　　电与放肆管理体系按排：低压电线电力电力电缆线敷设：趋势低压电线电力电力电缆线与放肆低压电线电力电力电缆线分槽敷设，趋势低压电线电力电力电缆线悦纳自己YJV-0.6/1kV型，放肆低压电线电力电力电缆线应用KVVP防线型，阻止电磁振动器搅扰；规格设计：在PLC放肆面板价格中布置脱附温湿度（180-220℃）、重复利用功率（更多功率的10%-15%）等关头规格，并止住PID自整定。　　Electrical and control system deployment: Cable laying: Power cables and control cables are laid in separate slots, with YJV-0.6/1kV power cables and KVVP shielded control cables to avoid electromagnetic interference; Parameter setting: Set key parameters such as desorption temperature (180-220 ℃) and regeneration air volume (10% -15% of rated air volume) in the PLC control panel, and perform PID self-tuning.

　　三、调试程序与工程竣工验收一阶段　　3、 Debugging and acceptance stage　　手机单机满载试正常的工作　　Single machine no-load trial operation　　机械设备測試：启动时传输机械设备，监测方案工作电流量妥协值≤±5%其他的工作电流量，不断日常运转2小时候，轴套温度升高≤40℃。　　Motor testing: Start the transmission motor, monitor the current fluctuation value to be ≤ ± 5% of the rated current, run continuously for 2 hours, and ensure that the bearing temperature rise is ≤ 40 ℃.　　良好的密封性圈性检侧：在进气口施用5kPa气压，保压30小时，气压降≤0.5kPa，考资格证书良好的密封性圈机器。　　Sealing test: Apply a pressure of 5kPa to the air inlet, maintain the pressure for 30 minutes, and verify the sealing performance with a pressure drop of ≤ 0.5kPa.　　联调阻抗测试仪　　Linkage load testing　　尾气预防流程步骤：通入摹拟尾气（VOCs质量渗透压500mg/m?），在线检测尾气排放标准口质量渗透压≤50mg/m?，去掉效力待定≥90%。　　Waste gas treatment process: Introduce simulated waste gas (VOCs concentration 500mg/m? ）Is the concentration at the discharge outlet ≤ 50mg/m? The removal efficiency is ≥ 90%.　　回收天道轮回资料显示：监测网脱附风温度表可不可一致在选用值±5℃数量内，RTO熄火空调温度度表≥760℃，确保安全生产硅酸物几乎腐蚀。　　Regeneration cycle verification: Monitor whether the desorption air temperature is stable within the set value ± 5 ℃ range, and the RTO combustion chamber temperature is ≥ 760 ℃ to ensure complete oxidation of organic matter.　　机器查看规范了　　Performance acceptance criteria　　防范风口尺寸：测试数据风口尺寸与想法值误差值≤±10%。　　Handling air volume: The deviation between the measured air volume and the design value is ≤± 10%.　　乐音控制：系统2米处乐音≤85dB(A)。　　Noise control: The noise level at a distance of 1 meter from the equipment is ≤ 85dB (A).　　文本转交：供给量几乎使用参考手册、守护日记怎么写网站模板及4年整车质保许诺书。　　Document handover: Provide a complete operation manual, maintenance log template, and a 3-year warranty commitment letter.

　　本文由沸石转轮废气处置友谊贡献.更多有关的常识请点击://www.hbsgqt.com咱们将会对您提出的疑难停止具体的解答，接待您登录网站留言.

　　This article is dedicated to the automatic shot blasting machine and friendship For more information, please click: //www.hbsgqt.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

上一篇：车间粉尘过量万万不要小视了粉尘的风险
下一篇：剖析车间全体除尘设备的焦点道理