一、在喷涂产出在线配置或吊件涂漆产品时要要慎重。成了担保浸涂时工件的制定计划在好的社会价值，我们是个人规划了它是经过了任务管理器试浸按时在喷涂产出在线依附吊具和物块的体例。被涂物块的大长相应紧邻竖直，另外长相应与阶段面成10°至40°角，便存留面漆顺遂地从被涂长相滴出。1、 Be careful when installing or hanging painted items on the painting production line. In order to ensure that the workpiece is placed in a good position during immersion coating, we have designed a method of attaching lifting tools and objects on the coating production line in advance through trial immersion. The large surface of the object to be coated should be close to vertical, and other surfaces should be at an angle of 10 ° to 40 ° to the horizontal plane, so that residual paint can flow out smoothly from the surface to be coated.二、都要对浸漆罐制止无球，减少车漆出产地网上营销涂漆时萃取剂离心分离到任务在日常生活中和浮尘跌入漆罐。2、 The paint immersion tank must be protected to prevent solvent diffusion to the workplace and dust from falling into the tank during painting on the paint production line.三、面漆产地线上线下对配件应对浸涂后，石油醚之基蒸发掉，乃能运至真空干燥室。3、 After immersion coating on large parts on the paint production line, the solvent basically evaporates and is then sent to the drying room.四、涂漆需要往往会看重精确测量腻子粉的粘合度，定期测粘合度1到1次，如果粘合度更具跨过原粘合度的10%之内，需实时的曾加萃取剂。曾加萃取剂时遏止浸渍支配。搅伴差不多后，精确测量粘合度后再遏止。4、 When painting, attention should be paid to measuring the viscosity of the coating regularly. Measure the viscosity once or twice per shift. If the viscosity increases by more than 10% of the original viscosity, solvent should be added in a timely manner. Stop the impregnation operation when adding solvent. After stirring evenly, measure the viscosity before proceeding.五、涂膜的板厚为关键性由喷漆工艺产地线上销售食品的落杆效率和喷漆工艺液的用户粘稠度草案。按以上的标准吃妻上瘾好漆液用户粘稠度后，油漆产地线应以涂膜z高效率30um玩弄，以区别装置所经流程试试看必定适的拉速。与此效率的一般地升任涂漆食品。如果是带动器效率快，纳米纳米涂层都会薄；如果是带动器效率慢，纳米纳米涂层都会厚且不的一般。5、 The thickness of the coating film is mainly determined by the lifting speed of objects on the coating production line and the viscosity of the coating liquid. After controlling the viscosity of the paint according to the above requirements, the paint production line should determine the appropriate pulling speed through experiments based on the high speed of the coating film, which is about 30um. Evenly lift the painted object at this speed. If the traction speed is fast, the coating will be thin; If the traction speed is slow, the coating will be thick and uneven.

六、在车漆物料染生产出来线上代理抑制浸涂时，涂漆沿海东南部和底层沿海东南部的漆面重量才可以差別，与此同时在被涂产品工件的底层边界上才可以堆砌出框厚的层。为了能努力车漆物料染的装潢品味，才可以用毛刷或通过向心血或防静电抽液转配清理除掉在浸渍守护进程中堆集的供过于求漆滴。6、 When dip coating is carried out on the paint production line, the paint film thickness of the painting area and the bottom area may be different, and a particularly thick layer may deposit on the bottom edge of the coated object. In order to improve the decorative quality of paint, excess paint droplets accumulated during the impregnation process can be manually removed using brushes or centrifugal force or electrostatic suction devices.七、在涂装设备原产线中浸湿材质件时，着重时间不会偏长，以避免出现木板读取产能过剩的水性油漆，减慢干燥数率，造成华侈。7、 When soaking wooden parts in the painting production line, be careful not to take too long to prevent the wood from absorbing excess paint, slowing down the drying speed, and causing waste.八、制止高沸点溶剂水蒸汽的其伤害，激发漏风机器设备，主要包括防震无法，按时查抄腻子粉出厂线。8、 Prevent damage from solvent vapors, strengthen ventilation equipment, take fire prevention measures, and regularly inspect paint production lines.

上一篇：车间焊接烟尘除尘器的挑选要注重甚么？
下一篇：涂装出产线设备布局特色先容