一、机制人涂装51漫画 线的废气名词解释：

1、 Brief description of exhaust gas from robot painting line:

在自动化设备厂人涂料线任务管理器中发现“三废”也不可放到的，此中喷涂工艺气体是“三废”的前提一部分。自动化设备厂人涂料线气体出自于就稀释液剂的易挥发物，有机物有机溶剂不能随刷漆粘附在车辆车辆汽修店的喷漆物长相，在车辆车辆汽修店的喷漆和固定任务管理器将全数开释，组合而成易挥发物性有机物物（VOCs），前提营养成分有苯、甲苯及二甲苯等苯系物下列不属于他非甲烷气体总烃等。车辆车辆汽修店的喷漆房和晒干室不待见气体中的VOCs氨水浓度很低，也是风速大，清洁物的前提营养成分为芳芬烃、醇醚类及酯类有机物物，之类自动化设备厂人涂料线发现的VOCs气体怎么样的正确处理？对于贵司常州鑫蓝环保型宽容沸石转轮就稀释液+离子液体熄火。

It is inevitable to generate "three wastes" during the process of robot painting line, among which spraying exhaust gas is the main part of the "three wastes". The exhaust gas from the robot painting line comes from the volatilization of diluents, and organic solvents will not adhere to the surface of the painted material with the paint. They will be completely released during the painting and curing process, forming volatile organic compounds (VOCs), mainly composed of benzene, toluene, xylene and other non methane hydrocarbons. The concentration of VOCs in the exhaust gas emitted from the spray booth and drying room is very low, but the air volume is high. The main components of pollutants are aromatic hydrocarbons, alcohol ethers, and ester organic compounds. How to treat the VOCs exhaust gas generated by this robot painting line? Our Kunshan Xinlan Environmental Protection adopts zeolite wheel concentration and catalytic combustion for this.

二、机人表面处理线尾气治理计划表：

2、 Waste gas treatment plan for robot painting line:

自动化设施设备人喷涂工艺线VOC废水所经过程中轴流风机保送生至转轮后，被转轮上的沸石离心分离到，从学习积极性平分离到到。在解离心分离到位置，所离心分离到的VOC用一齐比较小的热学习积极性（约180至250℃）吹扫，从沸石上脱附提升，此情此景VOC盐浓度值被直接掺水溶解就可以5至30倍。直接掺水溶解就可以后废水走进促使灭掉（CO)：废水中VOCs被直接掺水溶解就可以，调控混热器市场出清约100℃的小新风口尺寸温气流来暂停除尘器原理脱附。脱附到的高盐浓度值，小新风口尺寸直接掺水溶解就可以废水送进促使灭掉设施设备内促使灭掉细胞分化成CO2和H2O，灭掉放热的使用，节流趋势。

The VOC waste gas from the robot painting line is transported to the impeller by a fan and adsorbed by the zeolite on the impeller, which separates it from the air. In the desorption zone, the adsorbed VOCs are blown with a small amount of hot air (about 180 to 250 ℃) to desorb from the zeolite, and the VOC concentration is concentrated by 5 to 30 times. After concentration, the exhaust gas enters catalytic combustion (CO): VOCs in the exhaust gas are concentrated, and a small air flow of about 100 ℃ is provided by a mixer for back blowing desorption. The high concentration and low air volume concentrated exhaust gas desorbed is sent to the catalytic combustion equipment for catalytic combustion and decomposition into CO2 and H2O, which release heat for reuse and save energy.

三、机械设施人涂装51漫画 线气体正确处理设施特色化：

3、 Characteristics of exhaust gas treatment equipment for robot painting line:

1.CO离子液体灭掉专用设备容忍发芽势复合钯，镀铂在蜂窝陶瓷厂家承载上添为离子液体剂，纯利保障更是高达95%-99%，年限长，可二次利用，混合气体总流量大，内压小。

1. The CO catalytic combustion equipment uses high-quality palladium metal and platinum plated on a honeycomb ceramic carrier as a catalyst, with a pure profit efficiency of up to 95% -99%, long lifespan, renewability, high gas flow rate, and low resistance.

2.灵动工作具体具体措施具体具体措施一应俱全：消火栓自动喷淋系统、泄压孔、超温報警等无球工作具体具体措施具体具体措施。

2. Complete safety facilities: protective facilities such as fire sprinklers, pressure relief holes, and over temperature alarms.

3.显卡功耗：暖机15-3分之五钟全工作电压微波电加热，任何时只耗损排风机工作电压便可。当尾气溶度低时，主動中断挽救微波电加热。

3. Power consumption: Preheat for 15-35 minutes for full power heating, and only consume fan power during operation. When the concentration of exhaust gas is low, automatic intermittent compensation heating is used.

4.余热控制：余热可前去游玩无聊有效方法关闭无聊，大幅度降低原无聊有效方法的额定功率耗损。

4. Waste heat utilization: Waste heat can be returned to the drying path for drying, reducing the power consumption of the original drying path.

上一篇：灯杆喷涂流水线—主动喷粉设备的合作上风
下一篇：在基于产业4.0的涂装出产线中若何做到洁净出产？